Products catalog

  • Three-phase voltage and current relay | 3F+N | 100 A | U> 230–300 V | U< 140–240 V | DIN | ES-AVP3P-100

    Code: ES-AVP3P-100

    The ES-AVP3P-100 is a three-phase digital voltage relay that monitors the voltage of each phase and disconnects the load directly through its contacts.

  • Three-phase voltage and current relay | 3F+N | 100 A | U> 230–300 V | U< 140–240 V | DIN | ES-AVP3P-100

    The ES-AVP3P-100 is a three-phase digital voltage relay that monitors the voltage of each phase and disconnects the load directly through its contacts. In addition to voltage, it measures the load current and disconnects the circuit when the set limit is exceeded.

    Key point:
    One relay protects the whole three-phase supply or three-phase equipment: each phase is monitored separately and the load is disconnected automatically in case of a network fault.
    Load current
    1–100 A (30 A)
    Voltage limits
    U> 230–300 V · U< 140–240 V
    Network / supply
    3F+N
    Functions
    kWh meter, current limit

    How it works

    The relay is connected to the three-phase supply (with neutral, depending on the model); the voltage of each phase is measured separately.

    When the voltage in any phase leaves the limits, the load is disconnected; depending on the model, asymmetry, phase sequence or phase loss are also monitored. When the set current limit is exceeded, the load is also disconnected – this limits the power drawn.

    When the parameters return to normal, the load is reconnected after the set delay. The integrated meter accumulates the energy consumed (kWh).

    Why choose the ES-AVP3P-100?
    One device instead of several single-phase relays – less space in the board and a clear view of each phase.

    Technical specifications

    Product type Three-phase digital voltage and current relay (power type)
    Manufacturer / code ES-AVP3P-100
    Network 3F+N
    Rated current 100 A
    Overvoltage limit U> (factory) 230–300 V (270 V)
    Undervoltage limit U< (factory) 140–240 V (170 V)
    Current limit setting (factory) 1–100 A (30 A)
    Recovery delay (factory) 1–500 s (30 s)
    Display / indication LED, 8 digits
    Mounting DIN 35 mm

    Main functions

    • Monitoring of each phase – a fault is detected in any phase.
    • Over- and undervoltage protection – appliances are disconnected when the neutral breaks or the network fails.
    • Current limit – an overloaded circuit is disconnected, the power drawn is limited.
    • Phase loss monitoring – disconnects when a phase is lost.
    • Energy meter – you see how many kWh the circuit has consumed.
    • Digital display or indication – the status is visible at once.

    Where is it used?

    • Three-phase supplies of houses and country homes
    • Workshops, garages, farm buildings
    • Three-phase pumps, compressors, machine tools
    • Heat pumps with three-phase supply
    • Small production and storage premises

    Use by need

    For the owner of a three-phase house.
    One relay monitors all phases.
    For a workshop or farm owner.
    Three-phase equipment is disconnected on network faults.
    For the electrician.
    One device instead of several – fewer connections in the board.

    Practical use

    A workshop has a three-phase supply: machine tools and compressor are three-phase, lighting and sockets single-phase. If one phase fails, the ES-AVP3P-100 disconnects the load and reconnects it automatically when the parameters return.

    Pros

    • Monitors each phase
    • Automatic reconnection
    • One device instead of several
    • DIN mounting
    • Integrated kWh meter

    Cons / limitations

    • Does not protect against lightning and short surges – an SPD is needed
    • Does not replace circuit breakers and RCDs
    • IP20 – dry board only
    • The manufacturer does not publish a full datasheet – parameters per supplier specification

    Safety and installation notes

    • Install only after disconnecting the supply; work must be done by a qualified electrician.
    • Upstream – a circuit breaker with a current not higher than the relay's rated current.
    • Check phase and neutral wiring against the diagram.
    • Install the surge protective device (SPD) before the relay.

    Quick selection guide

    3F+N
    100 A
    U> 230–300 V
    U< 140–240 V
    Suitable when you need:
    • to protect a three-phase supply
    • to protect three-phase equipment
    • to monitor each phase
    Check before use:
    • main circuit breaker current ≤ 100 A
    • whether an N conductor is present if the model needs it
    Important reminder: the relay does not replace a surge protective device, circuit breakers or RCDs.

    FAQ

    Is a neutral conductor needed?
    For most three-phase voltage relays – yes, because the phase voltage is measured.
    Does it protect against lightning?
    No – an SPD is needed for that.
    What current should I choose?
    Not lower than the main circuit breaker current – the ES-AVP3P-100 suits up to 100 A.
    Does it disconnect all phases together?
    Depends on the model and mode – in SYN mode all phases are disconnected together.
    Are settings retained?
    Yes, the settings are kept during a power cut.
    Does it replace an RCD?
    No.

    Three-phase voltage and current relay | 3F+N | 100 A | U> 230–300 V | U< 140–240 V | DIN | ES-AVP3P-100

    ES-AVP3P-100 – protection of a three-phase supply and three-phase equipment against voltage and phase faults.

    Published: 2026-11-13 · Data verified against the supplier specification: 2026-11-13

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • Alternative products

    Modular | Digital Voltage Monitoring Relay | 1F | 63A | 230V | DIN | ETVPS1-63C
    Code: ETVPS1-63C
    This relay is designed to protect single-phase 230 V electrical installations and connected devices from overvoltage, undervoltage, and overcurrent. It is a practical solution for homes, workshops, farm facilities, technical rooms, and electrical panels where automatic monitoring of network parameters is required.
    Price 30.25 € VAT incl.
    ( 25.00 € VAT excl. )
    Single-phase voltage relay | 1F | 63 A | U> 270 V | U< 170 V | DIN | ESAVP-63
    Code: ESAVP-63

    The ESAVP-63 is a single-phase digital voltage relay for DIN-rail mounting in a distribution board.

    Price 32.50 € VAT incl.
    ( 26.86 € VAT excl. )
    Terminal clamp | electrical wire connector | universal | 2x0.2-4mm² | for all wire types | WAGO | 221-412 | 4050821808435
    Code: WAGO 221-412

    The WAGO 221-412 connector is one of the most popular and reliable electrical wire connection solutions in the world. It is designed for fast, safe, and professional connection of various types of copper conductors without the need for additional tools.

    Thanks to the patented CAGE CLAMP® technology and convenient orange levers, this connector allows quick connection of solid, stranded, and flexible conductors. The transparent housing enables visual inspection of the connection quality, while its compact dimensions allow easy installation in junction boxes, distribution boards, luminaires, and various automation equipment.

    The WAGO 221 series is widely used in residential, commercial, and industrial applications where reliable, standards-compliant, and long-lasting wire connections are required. 

    Price 0.30 € VAT incl.
    ( 0.25 € VAT excl. )
  • Subscribtion to new arrivals

    privacy policy

    Information