Products catalog

  • Power supply with relay for mirror demister pad control | 12 V DC | 24 W | 2 A | relay 1 A / 230 V AC | IP20 | ELSP-XMP-12V024W

    Code: ELSP-XMP-12V024W

    Compact 12 V DC 24 W power supply for mirrors with LED lighting and an anti-fog heating pad. The integrated 1 A / 230 V AC relay switches the pad without a separate module. 100–240 V AC input, insulation class II, overload, short-circuit and overheat protection, operating temperature −40…+40 °C.

  • Power supply with relay for mirror demister pad control | 12 V DC | 24 W | 2 A | relay 1 A / 230 V AC | IP20 | ELSP-XMP-12V024W

    Compact 24 W constant-voltage power supply for smaller mirrors with LED lighting and an anti-fog heating pad. One housing contains a 12 V DC output for lighting and electronics and an integrated 1 A / 230 V AC relay for the heating pad circuit. Insulation class II, overload, short-circuit and overheat protection.

    Key point:
    A smaller mirror (up to ~2 m of LED strip) does not need a 36 W supply. This 24 W model performs the same two tasks – it powers the 12 V lighting and switches the 230 V heating pad via the relay, so only one unit sits behind the mirror instead of two. Important: the pad is powered at 230 V through the relay, not from the 12 V output, so its power does not reduce the lighting budget.
    Output
    12 V DC, 2 A, 24 W
    Heating relay
    1 A / 230 V AC
    Dimensions
    130 × 43 × 21 mm
    Efficiency
    83 %, no-load < 0.5 W

    Operating principle

    The supply is installed behind the mirror or in a cabinet niche and connected to the 100–240 V AC mains via an H03VVH2-F 2×0.75 mm² primary lead. The secondary side has a 3×22AWG lead for the 12 V load – LED strip, touch or proximity switch and other mirror electronics.

    The switch-mode converter keeps a constant 12 V DC across the whole 0–2 A load range (tolerance ±2 %). The integrated relay switches the 230 V heating pad circuit up to 1 A. Wire according to the supplier wiring diagram.

    In case of overload (110–130 %) or short circuit, the supply enters hiccup mode and recovers automatically once the fault is removed. If it overheats, it shuts the output down – to restore operation, switch the supply off and on again.

    Why choose ELSP-XMP-12V024W?
    An optimal choice for smaller mirrors: compact 130 mm housing, power and heating control in one unit and no-load consumption below 0.5 W. If the LED load exceeds ~19 W, choose the 36 W model ELSP-XMP-12V036W.

    Technical specifications

    Product type Constant-voltage power supply with integrated relay for a mirror heating pad
    Product code ELSP-XMP-12V024W
    Output voltage 12 V DC (constant), tolerance ±2 %
    Rated current / range 2 A / 0–2 A
    Power 24 W
    Voltage regulation ±0.5 % (line), ±2 % (load)
    Ripple and noise max. 250 mVp-p
    Setup / hold-up time 500 ms / 100 ms (230 V AC), 1000 ms / 100 ms (115 V AC)
    Relay max. 1 A / 230 V AC, for the heating pad
    Input voltage / frequency 100–240 V AC / 47–63 Hz
    Input current 0.26 A (230 V AC), 0.5 A (115 V AC)
    Inrush current 40 A (230 V AC)
    Leakage current < 0.5 mA (240 V AC)
    Efficiency 83 %
    No-load consumption < 0.5 W
    Overload protection 110–130 %, hiccup mode, automatic recovery
    Short-circuit protection hiccup mode, automatic recovery
    Overheat protection output shut-down, restored by switching power off and on
    Insulation class II (double insulation)
    Insulation resistance input–output ≥ 50 MΩ (500 V DC, 25 °C, 70 % RH)
    Withstand voltage input–output 3.6 kV AC
    Protection rating IP20
    Operating temperature −40 … +40 °C (Tc max. 90 °C)
    Relative humidity 20–95 % RH, non-condensing
    Storage −40 … +90 °C, 10–95 % RH
    Dimensions 130 × 43 × 21 mm
    Weight 0.111 kg
    Primary lead H03VVH2-F 2×0.75 mm², length 90 ± 10 mm
    Secondary lead 3×22AWG, 80 °C, length 90 ± 10 mm
    Safety standards EN 61347-1, EN 61347-2-13
    EMC standards EN 55015, EN 61547, EN 61000-3-2, EN 61000-3-3

    Key functions

    • Constant 12 V DC – the LED strip shines evenly regardless of load changes.
    • Integrated 1 A / 230 V AC relay – the heating pad is switched without a separate control module.
    • Protections – overload and short circuit recover automatically, overheating shuts the output down.
    • Insulation class II – no protective earth conductor required.
    • No-load < 0.5 W – a permanently connected supply uses almost no energy while the mirror is off.
    • Wide operating temperature range – −40 … +40 °C.

    Where is it used?

    • Smaller bathroom mirrors with LED lighting and a heating pad
    • Mirror bathroom cabinets with integrated lighting
    • Hotel and apartment bathrooms
    • Replacing a failed mirror power supply

    Use by need

    For mirror manufacturers.
    One standard unit for lighting and heating of smaller mirrors – simpler kitting.
    For bathroom installers.
    Compact housing and short leads – wires are joined in a sealed junction box behind the mirror.
    For homeowners.
    Suitable for replacing a failed mirror supply when both lighting and heating must be kept.

    Practical example

    A 600 × 800 mm mirror has 2 m of 12 V LED strip (9.6 W/m, 19.2 W in total), a touch switch and a 400 × 300 mm 230 V heating pad. The supply powers the strip and the switch (about 80 % of its rating) and the relay switches the pad. With more than ~2 m of strip, the 36 W model would be needed.

    What else does the mirror kit need?

    The supply is the core of the kit. A complete mirror lighting and heating solution usually also needs:

    Anti-fog heating pad
    230 V, IP54, e.g. 400 × 300 mm pad. Pad current – no more than 1 A.
    12 V LED strip
    Total power up to 24 W (for continuous operation – up to ~19 W).
    Sealed junction box
    Junction box ELSP-XM-OJ-3319 (IP44) – for joining 230 V wires.

    Advantages

    • Power supply and heating control in one housing
    • Compact 130 × 43 × 21 mm housing
    • No-load < 0.5 W
    • Overload, short-circuit and overheat protection
    • Insulation class II, 3.6 kV AC withstand
    • Universal 100–240 V AC input, operation from −40 °C

    Disadvantages / limitations

    • 12 V load limited to 24 W (2 A) – larger lighting needs the 36 W model
    • Relay only up to 1 A / 230 V AC – a higher-current pad needs a separate relay
    • IP20 – install only where protected from splashes and condensation
    • Fixed 12 V – not for 24 V LED strips
    • After overheating, recovers only after power is switched off and on

    Safety and installation notes

    • Switch off the power before installation and make sure the circuit is dead.
    • Must be connected by a qualified electrician in line with bathroom zone requirements (HD 60364-7-701).
    • Install the IP20 supply behind the mirror or in a cabinet where no splashes reach it and no condensation forms.
    • The bathroom circuit must be protected by a 30 mA residual current device.
    • The heating pad current must not exceed 1 A.
    • Make 230 V connections in a sealed junction box.
    • Do not cover the housing with thermally insulating materials.

    Quick selection guide

    12 V DC | 2 A | 24 W
    Relay 1 A / 230 V AC
    130 × 43 × 21 mm
    IP20 | Class II
    Suitable when you need to:
    • power a 12 V LED strip and mirror electronics up to 24 W;
    • switch one heating pad up to 1 A / 230 V AC;
    • fit the power supply into a small mirror or cabinet.
    Check before use:
    • LED strip voltage (12 V) and total power;
    • heating pad current (no more than 1 A);
    • that the mounting location is protected from splashes and condensation.
    Important reminder: the supply does not replace circuit protection – a circuit breaker and a 30 mA residual current device. Dimming requires a switch with dimming function.

    Frequently asked questions

    What LED strip power can be connected?
    Up to 24 W (2 A) at 12 V; for continuous operation we recommend not exceeding ~19 W.
    Is the heating pad power included in the 24 W?
    No. The pad is powered at 230 V through the relay, so the 24 W limit applies only to 12 V lighting and electronics. For the pad, the relay limit of 1 A applies.
    How does it differ from the 36 W model?
    Lower 12 V power and a different housing. The 36 W model is slimmer (16.5 mm) and intended for larger mirrors.
    What if the supply overheats and shuts down?
    Switch the power off, remove the cause (covered housing, excessive load) and switch it on again.

    Power supply with relay for mirror demister pad | 12 V DC | 24 W | ELSP-XMP-12V024W

    ELSP-XMP-12V024W – compact 12 V DC 24 W power supply for mirror LED lighting with an integrated 1 A / 230 V AC relay for the heating pad. Insulation class II, 83 % efficiency, overload, short-circuit and overheat protection, compliant with EN 61347-1 and EN 61347-2-13.

    Published: 2026-11-12 · Data verified against the supplier specification: 2026-11-12

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • Alternative products

    Wireless control kit | actuator RFSA-61B and wall controller RFWB-40 | 866-916MHz | 230VAC | iNELS RF | RFSET-SW-F1
    Code: RFSET-SW-F1

    iNELS RF RFSET-SW-F1 is a wireless control kit: RFSA-61B actuator (230 V AC, 1 changeover contact 16 A AC1, 6 functions) and RFWB-40 wall controller (CR2032, about 5 years). RFIO2 communication up to 200 m, works without internet.

    Price 63.90 € VAT incl.
    ( 52.81 € VAT excl. )
    Flexible copper cable H05VV-F | 3G1.5 mm² | 300/500 V | round | white | 1 m | Lietkabelis
    Code: 92331501

    H05VV-F 3G1.5 mm² – AB Lietkabelis flexible round copper cable with class 5 conductors, PVC insulation and a white PVC sheath, 300/500 V. Sold by the metre.

    Cores: L, N, PE. Indicative current ≈ 16 A – for household appliances indoors.

    Price 1.04 € VAT incl.
    ( 0.86 € VAT excl. )
    Sealing protective mastic tape | 25x1x500mm | for sealing cable mechanical damage area | S1052-1-500
    Code: S 1052-1-500

    Specialized self-fusing sealing tape designed for protecting and sealing damaged areas on cables. Made from black thermoplastic, highly flowable mastic, this tape effectively shields cable insulation damage from moisture, corrosion, and dust. Used for emergency or preventive repair of electrical, telecommunication, and signal cables, especially suitable for outdoor and damp environments.

    Price 7.87 € VAT incl.
    ( 6.50 € VAT excl. )
    Smart lighting controller | dimmer | 150W LED / 200W | 100-240V | Wi-Fi | RF 433MHz | SONOFF | D1
    Code: SONOFF-D1

    SONOFF D1 is a smart Wi-Fi and RF 433 MHz lighting dimmer for dimmable LED lamps up to 150 W and incandescent lamps up to 200 W. Controlled with the eWeLink app, the RM433 remote and by voice. Installed in an EU / 86-type box.

    Price 17.40 € VAT incl.
    ( 14.38 € VAT excl. )
    Cable sheath and wire stripper 0.2–4.0 mm² | ErgoStrip KNIPEX
    Code: 169501SB

    KNIPEX high-quality, ergonomically designed wire and cable stripping tool for fast, precise, and safe work. This stripping knife is highly favored by professional electricians for its versatility, durability, and practical design. Suitable for removing insulation from both signal and power wires, as well as for installation, data, and coaxial cables.

    Perfectly suited for use on construction sites and in domestic installations, especially where wires need to be quickly and accurately prepared for connection in confined spaces. 

    Price 48.40 € VAT incl.
    ( 40.00 € VAT excl. )
  • Subscribtion to new arrivals

    privacy policy

    Information