Temperature and humidity sensor with LCD | Zigbee 2.4 GHz | 3 V (2× AAA) | IMOU ZTM1
Code: IOT-ZTM1-EUPrice 18.91 € VAT incl.( 15.62 € VAT excl. )Wireless Zigbee sensor for monitoring room temperature and relative humidity. Shows readings on its LCD and sends them via the Imou Zigbee gateway to the Imou Life app. Powered by 2× AAA batteries.
-
Temperature and humidity sensor with LCD | Zigbee 2.4 GHz | 3 V (2× AAA) | IMOU ZTM1
IMOU ZTM1 is a battery sensor that measures room temperature and relative humidity. Readings are shown on the LCD display and in the Imou Life app. Communication: Zigbee 2.4 GHz, power: 3 V (2× AAA), temperature error: ±0.3 °C.
Key point:
No wiring needed: place or stick the sensor and see the indoor climate on site and on your phone. It lets you monitor a flat, basement, storeroom or server room without an electrician. An Imou Zigbee gateway is required.Communication
Zigbee 2.4 GHzTemperature error
±0.3 °CPower supply
2× AAA, 3 VDimensions
Φ61 × 23 mmCommunication interfaces and integration
Zigbee 2.4 GHz (≤15 dBm) Data goes to the Imou Zigbee gateway and from there to the Imou cloud and app. Imou Life app Current readings and change history for up to 1 year. Zigbee2MQTT The community device list marks model ZTM1-EN as supported – suitable for Home Assistant setups with their own Zigbee coordinator. Operating principle
Insert 2× AAA batteries and pair the sensor with the Imou Zigbee gateway in the Imou Life app. Place it on the stand or stick it to the wall with the 3M pad.
The sensor measures temperature and relative humidity, shows them on the LCD and sends them to the gateway over Zigbee. Standby current is up to 30 µA, so the batteries last more than a year.
You see current values and history on your phone. When battery voltage drops to 2.5 ± 0.2 V, the sensor reports low battery.
Why choose the IMOU ZTM1?
ZTM1 shows the real indoor climate where running a cable is not practical. The display lets you check values without a phone, and the history helps spot humidity peaks and cold periods.Technical specifications
Product type Wireless temperature and humidity sensor with LCD Manufacturer / model IMOU ZTM1 (IOT-ZTM1-EU) Communication Zigbee, 2.4 GHz, transmit power ≤15 dBm Communication range up to 1200 m in open space (manufacturer data); much shorter indoors Power supply 3 V DC, 2× AAA batteries Battery life > 1 year (manufacturer data) Current consumption standby ≤30 µA, operating ≤30 mA Low voltage alarm 2.5 ± 0.2 V Temperature error ±0.3 °C Humidity error ±2–3 % RH (per distributor data) Operating temperature −10…+55 °C Display LCD, temperature and humidity Data history up to 1 year (Imou cloud) Dimensions Φ61 × 23 mm Mounting on a table (stand) or on a wall (3M pad) Required Imou Zigbee gateway, Imou Life app Key functions
- LCD display – temperature and humidity visible without a phone
- Zigbee communication – low power consumption, long battery life
- History up to 1 year – see when the room was too damp or too cold
- Battery power – installation without wiring or an electrician
- Low voltage alarm – replace batteries in time
- Two mounting options – stand or 3M pad
How does it differ from similar products?
SONOFF SNZB-02DR2 (18621) Also a Zigbee sensor with LCD, additionally shows VPD. Choose based on the gateway ecosystem you already use. LoRa T/RH sensor IP65 (15791) Designed for outdoor conditions and long distances. ZTM1 is for indoor use only, no IP rating stated. LEFOO LFH10 (11907) Wired transmitter with 4–20 mA / 0–10 V / RS485 output for automation. ZTM1 is for monitoring, not for a controller. Where is it used?
- Flats and houses – bedroom, children's room
- Basement, laundry room – humidity monitoring
- Storerooms and heated garages
- Server or network cabinet rooms
- Rental properties – remote supervision
- Storage of books, tools, plants
Use by need
For beginners.
Insert the batteries, pair in Imou Life and place the sensor away from radiators and direct sun.For experienced installers.
Spread several sensors across floors and check the link to the gateway at each spot before fixing them.For engineers / designers.
If a controller needs a 0–10 V, 4–20 mA or Modbus signal, ZTM1 is not suitable – choose a wired transmitter such as LEFOO LFH10.Practical application
Situation: a house basement smells damp in autumn, but it is unclear when humidity rises. Solution: a ZTM1 is placed on a shelf and paired with the Imou Zigbee gateway. Result: after a week the history shows humidity jumps after laundry drying. A dehumidifier is switched on and ventilation is adjusted accordingly.Pros / advantages
- Installation without wiring or an electrician
- LCD display – values visible on site
- Temperature error ±0.3 °C
- History up to 1 year
- Compact: Φ61 × 23 mm
- Batteries last more than a year
Cons / limitations
- Requires the Imou Zigbee gateway or your own Zigbee coordinator with Zigbee2MQTT
- No IP rating stated – indoor only; for outdoors choose the LoRa T/RH IP65 sensor (15791)
- No analogue or Modbus output – for automation choose LEFOO LFH10 (11907)
- Measuring ranges are not published by the manufacturer
Safety and installation notes
- Use indoors only, operating temperature −10…+55 °C.
- Do not place near radiators, cookers or in direct sunlight – readings will be distorted.
- Replace both AAA batteries together and observe polarity.
- Do not mount where water splashes or condensation can reach the sensor.
- Hand in used batteries at a battery collection point.
Quick selection guide
Zigbee 2.4 GHz±0.3 °C2× AAA, 3 VΦ61 × 23 mmSuitable when you need:- to monitor temperature and humidity on your phone
- to see values on a display on site
- to install without wiring
- to keep up to 1 year of history
Check before choosing:- whether you have an Imou Zigbee gateway
- whether room temperature stays within −10…+55 °C
- whether a controller needs a signal (0–10 V, 4–20 mA, Modbus)
- whether the Zigbee link reaches the gateway through walls
Important reminder: ZTM1 is a monitoring sensor. It has no relay output and does not control a dehumidifier or heater by itself. Control requires a hygrostat, thermostat or automation with relays.☝ Elsprendimai.eu recommends:- SONOFF SNZB-02DR2 – SONOFF SNZB-02DR2 – Zigbee sensor with LCD and VPD if you use another Zigbee ecosystem.
- Renke RS-WS-LORA-2-EX – LoRa T/RH sensor IP65 – when you need to measure outdoors or over long distances.
- Thermostats – Thermostats – when temperature must be controlled, not only displayed.
- Temperature and humidity sensor selection guide – Temperature and humidity sensor guide – a quick comparison of all types in the group.
FAQ
Does ZTM1 work without a gateway?
With the Imou Life app – no, an Imou Zigbee gateway is required. The Zigbee2MQTT community list marks ZTM1 as supported with your own Zigbee coordinator.Does the range really reach 1200 m?
This is the manufacturer's open-space value without obstacles. Indoors, through walls and floors, the range is much shorter.Which batteries are used?
2× AAA, total voltage 3 V. The manufacturer states a battery life of more than 1 year.Can it be mounted outdoors?
No. No IP rating is stated and the operating temperature is −10…+55 °C. For outdoors choose the LoRa T/RH IP65 sensor.How long is the history stored?
The manufacturer states that temperature and humidity changes are kept for up to 1 year in the Imou cloud.Can the sensor switch on a dehumidifier?
No, it has no relay output. To control a dehumidifier use a hygrostat such as STC-3028 or XH-W3005.Sources: IMOU IOT-ZTM1-EU datasheet, distributor specification (scom.hu), Zigbee2MQTT device list. Checked 2026-10-19.
IMOU ZTM1 Zigbee temperature and humidity sensor
IMOU ZTM1 is a wireless Zigbee temperature and humidity sensor with LCD display, 2× AAA batteries and up to 1 year of history. It suits flats, basements, storerooms and server rooms where the indoor climate must be monitored without wiring.
Published: 2026-10-19 · Data verified against the supplier's data: 2026-10-19
Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.ManufacturerThis product is marked with the CE label, which confirms that it complies with all applicable European Union directives and regulations. CE marking is not just a formality – it is an important indicator of quality and safety, ensuring that the product has been properly assessed, tested, and can be safely used throughout the EU market.
CE certification means that the product has been evaluated according to the main criteria:
Safety requirements – ensures that the product does not pose a risk to the user or the environment
Electromagnetic compatibility (EMC) – the device does not interfere with other equipment and is resistant to external disturbances
Environmental standards – complies with current ecological and material usage requirements
Operational reliability – the product is suitable for long-term use according to its intended purposeCE marking allows this product to:
be legally supplied and used in all European Union countries
ensure a high level of quality and safety
be used in residential, commercial, and industrial environmentsThe CE mark is a declaration of the manufacturer’s responsibility, confirming that the product complies with all applicable standards and has been assessed according to EU legislation.
What does this mean for you as a buyer?
Safe use in everyday activities
Reliable performance and reduced risk of failure
Compliance with EU standards and requirements
Suitability for professional solutions
Love it? Share your thoughts in a review!Write Review Alternative products
IP surveillance camera | Turret | 4 MP | 2.8 mm | IR 30 m | WDR 120 dB | PoE | IP66 | Hikvision DS-2CD2345FWD-ICode: DS-2CD2345FWD-IHikvision DS-2CD2345FWD-I is a 4 MP (2688 × 1520) turret camera with a 1/2.5" sensor, 120 dB WDR and IR up to 30 m. Line-crossing, intrusion and unattended-object detection, H.265+, PoE 802.3af, microSD up to 128 GB, IP66.
Price 137.00 € VAT incl.( 113.22 € VAT excl. )












