8in1 soil sensor | moisture, temperature, EC, salinity, pH, N, P, K | RS485 Modbus RTU, LoRa / LoRaWAN | IP68 | RD-NPKMTEPH-L-01
Code: ES-RD-NPKMTEPH-L-01Price 50.67 € VAT incl.( 41.88 € VAT excl. )One probe – eight soil parameters: moisture, temperature, EC, salinity, pH and N, P, K. Data via RS485 Modbus RTU or LoRa / LoRaWAN, IP68 housing – stays in the ground permanently.
-
8in1 soil sensor | moisture, temperature, EC, salinity, pH, N, P, K | RS485 Modbus RTU, LoRa / LoRaWAN | IP68 | RD-NPKMTEPH-L-01
RD-NPKMTEPH-L-01 is an integrated soil sensor measuring 8 parameters: moisture, temperature, electrical conductivity (EC), salinity, pH and nitrogen, phosphorus and potassium (N, P, K). The probe is inserted into the soil and stays there permanently – IP68 housing. Data is transmitted via RS485 Modbus RTU or wireless LoRa / LoRaWAN.
Key point:
Instead of several separate sensors – one probe and one cable or radio node. Irrigation and fertilising decisions can be based on continuous measurements, not a one-off sample. Especially useful in greenhouses and remote fields you will not visit daily.Parameters
8: moisture, T, EC, salinity, pH, N, P, KInterface
RS485 Modbus RTU + LoRa / LoRaWANProtection
IP68Response
<1 sCommunication interfaces and integration
RS485 Modbus RTU Wired connection to a PLC, data logger or gateway; default address 01, several sensors on one line with different addresses. LoRa / LoRaWAN Wireless transmission from the field without cables. Confirm the frequency band (EU – 868 MHz) and network type before ordering. Operating principle
The probe is inserted vertically or horizontally into the soil at the desired root-zone depth. The electrodes must be in full contact with the soil, with no air gaps or stones.
After power-on, readings stabilise within 5–10 s. The sensor measures moisture, temperature, EC, salinity, pH and N, P, K and provides them in Modbus registers.
Data goes via RS485 or LoRa / LoRaWAN to a controller or platform – you see trends and can control irrigation and fertilising according to actual soil conditions.
Why choose RD-NPKMTEPH-L-01?
Eight measurements in one IP68 probe save installation work and connections. Two interfaces give a choice: cable near the controller or radio in a remote field.Technical specifications
Product type Integrated 8-parameter soil sensor Manufacturer / model OEM (manufacturer not confirmed) / RD-NPKMTEPH-L-01 Measured parameters Moisture, temperature, EC, salinity, pH, nitrogen (N), phosphorus (P), potassium (K) Moisture range 0–100 % N, P, K range 0–1999 mg/kg (per OEM data) pH accuracy ±0.3 pH (per supplier data) Response time <1 s Stabilisation after power-on 5–10 s Operating temperature −30…+70 °C (per supplier data) Wired interface RS485, Modbus RTU, default address 01 Wireless communication LoRa / LoRaWAN (per supplier data) Ingress protection IP68 Housing material ABS plastic + epoxy resin Cable length 1 m (per supplier data) Key functions
- Soil moisture and temperature – for irrigation control and frost risk assessment.
- EC and salinity – to monitor fertiliser concentration and salinisation.
- pH – to track soil acidity trends.
- N, P, K – indicative nutrient dynamics between laboratory tests.
- RS485 Modbus RTU – directly to a PLC, logger or gateway.
- LoRa / LoRaWAN – data from a remote field without cables.
How does it differ from similar products?
22727 Sentera SWCSM-075 Measures only soil moisture and temperature, Modbus RTU, IP67 – simpler when pH, EC and NPK are not needed. 15791 Renke RS-WS-LORA-2-EX LoRa air temperature and humidity sensor, not for soil – suits greenhouse air monitoring alongside this probe. 22719 Sentera ODTHM Outdoor air T/RH sensor with Modbus RTU, IP65 – for weather conditions, not soil. Where is it used?
- Greenhouses and vegetable growing
- Field farming and precision agriculture
- Orchards, berry plantations and vineyards
- Drip irrigation and fertigation systems
- Seedling nurseries and tree nurseries
- Golf courses and sports turf
- Agronomic trial plots
- Landscaping and park maintenance
Use by need
For beginners.
Insert the probe into stone-free soil and connect it to a ready-made logger or gateway – the system reads the registers.For experienced installers.
When connecting several probes on one RS485 line, change the addresses (default 01), use shielded twisted-pair cable and termination resistors.For engineers / designers.
When designing, consider measuring depth, probe density in the field, LoRa frequency band and data interval.Practical application
In a greenhouse, tomatoes are watered on a timer, so the soil is waterlogged in some places and dry in others. 8in1 probes were inserted in three zones, with data collected via RS485 into a controller. Irrigation now starts based on actual moisture, and EC shows when the nutrient solution is too strong. Water and fertiliser consumption becomes controlled.Pros / advantages
- 8 parameters in one probe
- Two interfaces: RS485 Modbus RTU and LoRa / LoRaWAN
- IP68 – stays in the soil permanently
- Fast response – <1 s
- ABS + epoxy housing, moisture resistant
- Simple integration via standard Modbus
Cons / limitations
- N, P, K values are indicative – they do not replace laboratory soil analysis
- LoRa frequency band and power supply not confirmed – check before ordering
- Measures one point – a large field needs several probes
- Does not control irrigation itself – a controller or PLC is required
- If only moisture and temperature are needed – the simpler 22727 Sentera SWCSM-075
Safety and installation notes
- Do not hammer the probe or push it into stony soil – the electrodes are easily damaged.
- Make field cable joints in an IP67/IP68 junction box or seal them with heat-shrink tubing.
- Provide surge protection for long outdoor RS485 lines.
- ⚡ If the power supply is connected to 230 V mains, it must be installed by a qualified electrician with a circuit breaker.
- Before the season, clean the electrodes and check readings against a reference sample.
Quick selection guide
8 parameters incl. NPKRS485 Modbus RTULoRa / LoRaWANIP68Suitable when you need:- to monitor soil moisture and nutrients continuously
- to control irrigation and fertigation based on actual data
- to transmit data from a remote field without cables
- to integrate soil data into a PLC or SCADA
Check before choosing:- LoRa / LoRaWAN frequency band (EU – 868 MHz) and network type
- supply voltage and whether the LoRa version has a battery
- the pH measuring range for your soil
- cable length to the logger (standard – 1 m)
Important reminder: ⚠ N, P, K readings are for tracking trends – confirm fertiliser rates with laboratory soil analysis. The sensor only measures; irrigation and fertilising are controlled by your controller.☝ Elsprendimai.eu recommends:- Sentera SWCSM-075 – When only soil moisture and temperature are needed – a simpler Modbus RTU probe, IP67.
- Renke RS-WS-LORA-2-EX – For greenhouse air monitoring – wireless battery-powered LoRa T/RH sensor.
- Temperature and humidity sensor selection guide – Group selection guide: how to choose a sensor by measured medium and communication.
- Sensors and detectors – The full sensors and transmitters group: pressure, level, air quality and other sensors.
FAQ
Which 8 parameters does the sensor measure?
Moisture, temperature, electrical conductivity (EC), salinity, pH and nitrogen, phosphorus and potassium (N, P, K).Are N, P, K readings as accurate as a laboratory?
No. They are indicative values for tracking trends. Use laboratory analysis for fertilising decisions.How do I connect it to a PLC?
Via RS485 Modbus RTU. Default address is 01 – change the addresses when connecting several probes.Does the sensor work with a LoRaWAN network?
The supplier states LoRa / LoRaWAN. Confirm the frequency band (EU – 868 MHz) and compatibility with your network before ordering.Can it stay in the soil for the whole season?
Yes, the IP68 housing is designed for permanent in-soil measurement.How long do readings take to stabilise?
5–10 s after power-on; response to changes is <1 s.Sources: OEM 8in1 soil sensor specifications (Honde, Cloudtronics, BGT), existing supplier data. No datasheet from the specific manufacturer found. Checked 2026-10-19.
8in1 soil sensor RD-NPKMTEPH-L-01
An integrated IP68 soil sensor measuring moisture, temperature, EC, salinity, pH and N, P, K. Data via RS485 Modbus RTU or LoRa / LoRaWAN for irrigation and fertilising control.
Published: 2026-10-19 · Data verified against the supplier's data: 2026-10-19
Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.This product is marked with the CE label, which confirms that it complies with all applicable European Union directives and regulations. CE marking is not just a formality – it is an important indicator of quality and safety, ensuring that the product has been properly assessed, tested, and can be safely used throughout the EU market.
CE certification means that the product has been evaluated according to the main criteria:
Safety requirements – ensures that the product does not pose a risk to the user or the environment
Electromagnetic compatibility (EMC) – the device does not interfere with other equipment and is resistant to external disturbances
Environmental standards – complies with current ecological and material usage requirements
Operational reliability – the product is suitable for long-term use according to its intended purposeCE marking allows this product to:
be legally supplied and used in all European Union countries
ensure a high level of quality and safety
be used in residential, commercial, and industrial environmentsThe CE mark is a declaration of the manufacturer’s responsibility, confirming that the product complies with all applicable standards and has been assessed according to EU legislation.
What does this mean for you as a buyer?
Safe use in everyday activities
Reliable performance and reduced risk of failure
Compliance with EU standards and requirements
Suitability for professional solutions
Love it? Share your thoughts in a review!Write Review Alternative products
IP surveillance camera | Turret | 4 MP | 2.8 mm | IR 30 m | WDR 120 dB | PoE | IP66 | Hikvision DS-2CD2345FWD-ICode: DS-2CD2345FWD-IHikvision DS-2CD2345FWD-I is a 4 MP (2688 × 1520) turret camera with a 1/2.5" sensor, 120 dB WDR and IR up to 30 m. Line-crossing, intrusion and unattended-object detection, H.265+, PoE 802.3af, microSD up to 128 GB, IP66.
Price 137.00 € VAT incl.( 113.22 € VAT excl. )












