Products catalog

  • Automatic transfer switch ATS CHINT NXZM-160S/3 | 3P | 125 A | 400/415 V | CB class

    Code: ES-NXZM-160S-125
    Price 534.48 € VAT incl.
    ( 441.72 € VAT excl. )
    Buy more, pay less
    10+ pcs.  – 237.16 € for pcs. -55%

    CHINT NXZM-160S/3 – 3P automatic transfer switch 125 A for a three-phase 400/415 V system with two power sources. CB class: switching is done by NXM circuit breakers, so overload and short-circuit protection is built in (Icn 35 kA).

  • Automatic transfer switch ATS CHINT NXZM-160S/3 | 3P | 125 A | 400/415 V | CB class

    CHINT NXZM-160S/3 is automatic transfer switching equipment (ATS) that transfers the load to a backup source – a second grid supply or a generator – when the main supply fails or goes out of limits. 3P, rated current 125 A, operating voltage 400/415 V, 50 Hz.

    Key point:
    A CB class ATS consists of two NXM series circuit breakers with a motor drive and a controller. It therefore not only transfers the sources but also protects the circuit against overload and short circuit: rated short-circuit breaking capacity Icn 35 kA (S type).
    Poles / current
    3P / 125 A
    Class (IEC 60947-6-1)
    CB
    Transfer time
    3.3 s ±10 %
    Utilisation category
    AC-33B

    How it works

    The controller continuously measures the voltage of both sources. If a phase is lost or the voltage leaves the set limits (undervoltage – default 187 V, adjustable 160–200 V; overvoltage – 263 V, adjustable 240–290 V), after the set delay the ATS disconnects the main source and connects the backup.

    The controller has three modes: grid–grid with automatic return, grid–grid without automatic return and grid–generator. Transfer, return, generator start and stop delays are adjustable 0–180 s (default 5 s).

    The generator start contact (601–603) and fire-control feedback are available only with the B type (intelligent) controller – the A type controller does not control a generator. Sources are connected at the top, the load at the bottom.

    Why choose CHINT NXZM-160S/3?
    One device transfers the sources, protects the circuit against overload and short circuit and prevents the grid from being connected to the backup source.

    Technical specifications

    Product type Automatic transfer switching equipment (ATS), CB class
    Manufacturer / model CHINT, NXZM-160S/3 125 A
    Poles 3P
    Rated current In 125 A (frame 160 A)
    Operating voltage Ue 400/415 V, 50 Hz
    Insulation voltage Ui AC 800 V
    Utilisation category AC-33B
    Short-circuit making capacity Icm S: 73.5 kA (H type: 105 kA)
    Short-circuit breaking capacity Icn S: 35 kA (H type: 50 kA)
    Transfer time operating 3.3 s ±10 %
    Endurance mechanical 8 000, electrical 2 000 cycles
    Controller supply Us 230/240 V, 50 Hz; 85–110 %
    Controller A (standard) or B (intelligent); integrated or split mounting
    Voltage limits undervoltage 160–200 V (187 V), overvoltage 240–290 V (263 V)
    Delays 0–180 s (default 5 s)
    Communication RS485, Modbus (B type controller)
    Operating conditions −5…+40 °C, up to 2000 m, pollution degree 3
    Standards IEC 60947-1, IEC 60947-6-1
    Data according to the CHINT NXZ(H)B / NXZ(H)M catalogue. The exact version (S or H, A or B controller) is shown on the product label – please confirm before ordering.

    Key functions

    • Automatic transfer – on phase loss, undervoltage or overvoltage.
    • Overload and short-circuit protection – NXM circuit breakers, Icn 35 kA.
    • Three modes – grid–grid with or without return, grid–generator.
    • Manual operation and position 0 – both sources disconnected for maintenance.
    • Fault indication, fire-control input, RS485 – depending on the controller type.

    How does it differ from similar switches?

    • CHINT NXZM-160S/3 160 A – higher rated current – 160 A.
    • CHINT NXZ (PC class) – no built-in protection, circuit breakers or fuses are needed upstream.
    • Modular DIN ATS up to 125 A – for homes and small sites; CHINT NXZM – for switchboards and higher currents.

    Where is it used?

    • Main switchboards of industrial and commercial buildings – dual supply backup.
    • Sites with a backup generator – factories, warehouses, farms.
    • Hospitals, server rooms, telecom nodes – where a power interruption is costly.
    • High-rise buildings – supply of fire safety systems, fire-control input.
    • Residential houses – three-phase supply with a generator.

    Use by need

    For switchboard builders.
    A factory-made ATS with controller – less mounting and commissioning.
    For power engineers.
    Dual supply or grid–generator backup with adjustable limits and delays.
    For building owners.
    Power is restored automatically – without human intervention.

    Practical use

    Example: a site supply up to 125 A and a backup generator. The ATS is mounted in the switchboard between the supply and load busbars, the controller is set to grid–generator mode and the generator remote start input is connected to contact 601–603 of the B type controller. When the grid fails the generator starts, and the load is transferred only when its voltage reaches the set limits.

    Advantages

    • Built-in protection – Icn 35 kA (S type).
    • Adjustable voltage limits and delays.
    • Three operating modes – for grid and generator.
    • Factory-made CHINT solution – drive and controller in one.
    • Mechanical endurance – 8 000 cycles.

    Disadvantages / limitations

    • Generator control only with the B type controller.
    • There is a short interruption during transfer – this is not a UPS.
    • Larger than modular ATS – needs switchboard space.
    • The controller needs a correctly connected N – a mistake can damage it.

    Safety and installation notes

    • Before work, disconnect both sources and switch the controller to manual mode – the ATS can transfer automatically.
    • Phase sequence and N – the manufacturer warns that a wrongly connected N can burn the controller.
    • Sources are connected at the top, the load at the bottom; vertical or horizontal mounting.
    • Select cables and busbars for 125 A and the manufacturer's terminal dimensions.
    • Installation by a qualified electrician; the generator N–PE bond according to the site earthing system.
    ☝ Elsprendimai.eu recommends: ATS selection guide · Diagrams: 3P or 4P · Ask for selection

    Quick selection guide

    Choose CHINT NXZM-160S/3 if the supply is up to 125 A, the system is 400/415 V and you need an ATS with built-in short-circuit protection.

    3P · 125 A
    400/415 V
    CB · IEC 60947-6-1
    AC-33B
    Suitable when you need:
    • dual supply or grid–generator backup up to 125 A;
    • a three-phase 400/415 V system;
    • short-circuit protection in the ATS itself.
    Check before use:
    • the number of poles – 3P or 4P (N switching);
    • the controller type – a generator needs B;
    • switchboard space and cable cross-section for 125 A.
    Important: An ATS does not replace a design – the number of poles, protection and generator connection are confirmed by the designer.

    FAQ

    Can CHINT NXZM-160S/3 start a generator?
    Yes, if a B type (intelligent) controller is ordered – contact 601–603 closes when the main source fails. The A type controller does not control a generator.
    How long does the transfer take?
    The operating transfer time of the mechanism is 3.3 s ±10 %, plus the set delay (0–180 s).
    Is protection needed upstream of the ATS?
    A CB class ATS already has NXM circuit breakers (Icn 35 kA). Selectivity with the supply protection is confirmed by the designer.
    What voltage limits can be set?
    Undervoltage – 160–200 V (default 187 V), overvoltage – 240–290 V (default 263 V).
    3P or 4P?
    NXZM-160S/3 is the 3P version: N is not switched and an external N wire is connected to the controller. If the generator N is bonded to PE, choose the 4P version.
    Can it be controlled remotely?
    The B type controller has an RS485 (Modbus) interface – status and parameters can be sent to the building management system.

    Automatic transfer switch ATS CHINT NXZM-160S/3 | 3P | 125 A | 400/415 V | CB class

    CHINT NXZM-160S/3 – CB class 3P automatic transfer switch 125 A for 400/415 V systems with two sources: built-in protection, adjustable voltage limits, delays and three operating modes.

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • Alternative products

    U-FTP Cable | 6A CAT | 4x2x23 AWG | shielded | copper | UV resistant | outdoor use | black
    Code: KIF6AOUTS500

    The U/FTP cable is a high-quality four-pair data transmission cable designed for telecommunication, industrial, and outdoor network installations. This cable is 100% copper, ensuring maximum signal transmission efficiency and minimal signal attenuation.

    It is adapted for 10 Gigabit Ethernet (10GBASE-T) data transmission at speeds of up to 10,000 Mbps and provides high electromagnetic resistance, as each pair is shielded with aluminum foil. Thanks to the PE outer layer, the cable is resistant to moisture, UV radiation, and mechanical impact, making it ideal for outdoor installations. 

    Price 0.73 € VAT incl.
    ( 0.60 € VAT excl. )
    Network plug | RJ45 connector (8P8C) | for UTP CAT 6e cable | unshielded | through-plug | transparent
    Code: WT117

    This RJ45 Cat.6 UTP modular plug is a high-quality 8P8C unshielded network connector type, designed for Cat.6 UTP (Unshielded Twisted Pair) cables. The special straight-through design makes cable termination easier and more convenient, as the wires can be threaded through the plug, allowing a visual check of the wire arrangement before crimping the connector.

    Price 0.20 € VAT incl.
    ( 0.17 € VAT excl. )
    Solar PV cable | H1Z2Z2-K | 1x4 mm² | black | 1.5 kV DC | EN 50618 | Dca | IEMMEQU HAR
    Code: H1Z2Z2K

    The cable is designed for connecting photovoltaic (solar energy) systems and interconnecting solar modules. This cable offers excellent resistance to ultraviolet (UV) rays, ozone, atmospheric effects, and temperature fluctuations. A durable and flexible single-core copper cable with double insulation ensures long service life and safe use even in the most challenging outdoor conditions. Suitable for installation both indoors and outdoors.

    Price 0.98 € VAT incl.
    ( 0.81 € VAT excl. )
  • privacy policy

    Information