Automatic transfer switch ATS CHINT NXZM-630S/3 | 3P | 630 A | 400/415 V | CB class
Code: ES-NXZM-160S-630Price 1137.40 € VAT incl.( 940.00 € VAT excl. )Buy more, pay less10+ pcs. – 796.18 € for pcs. -30%CHINT NXZM-630S/3 – 3P automatic transfer switch 630 A for a three-phase 400/415 V system with two power sources. CB class: switching is done by NXM circuit breakers, so overload and short-circuit protection is built in (Icn 50 kA).
-
Automatic transfer switch ATS CHINT NXZM-630S/3 | 3P | 630 A | 400/415 V | CB class
CHINT NXZM-630S/3 is automatic transfer switching equipment (ATS) that transfers the load to a backup source – a second grid supply or a generator – when the main supply fails or goes out of limits. 3P, rated current 630 A, operating voltage 400/415 V, 50 Hz.
Key point:
A CB class ATS consists of two NXM series circuit breakers with a motor drive and a controller. It therefore not only transfers the sources but also protects the circuit against overload and short circuit: rated short-circuit breaking capacity Icn 50 kA (S type).Poles / current
3P / 630 AClass (IEC 60947-6-1)
CBTransfer time
3.5 s ±10 %Utilisation category
AC-33BHow it works
The controller continuously measures the voltage of both sources. If a phase is lost or the voltage leaves the set limits (undervoltage – default 187 V, adjustable 160–200 V; overvoltage – 263 V, adjustable 240–290 V), after the set delay the ATS disconnects the main source and connects the backup.
The controller has three modes: grid–grid with automatic return, grid–grid without automatic return and grid–generator. Transfer, return, generator start and stop delays are adjustable 0–180 s (default 5 s).
The generator start contact (601–603) and fire-control feedback are available only with the B type (intelligent) controller – the A type controller does not control a generator. Sources are connected at the top, the load at the bottom.
Why choose CHINT NXZM-630S/3?
One device transfers the sources, protects the circuit against overload and short circuit and prevents the grid from being connected to the backup source.Technical specifications
Product type Automatic transfer switching equipment (ATS), CB class Manufacturer / model CHINT, NXZM-630S/3 630 A Poles 3P Rated current In 630 A (frame 630 A) Operating voltage Ue 400/415 V, 50 Hz Insulation voltage Ui AC 1000 V Utilisation category AC-33B Short-circuit making capacity Icm S: 105 kA (H type: 154 kA) Short-circuit breaking capacity Icn S: 50 kA (H type: 70 kA) Transfer time operating 3.5 s ±10 % Endurance mechanical 4 000, electrical 1 500 cycles Controller supply Us 230/240 V, 50 Hz; 85–110 % Controller A (standard) or B (intelligent); integrated or split mounting Voltage limits undervoltage 160–200 V (187 V), overvoltage 240–290 V (263 V) Delays 0–180 s (default 5 s) Communication RS485, Modbus (B type controller) Operating conditions −5…+40 °C, up to 2000 m, pollution degree 3 Standards IEC 60947-1, IEC 60947-6-1 Data according to the CHINT NXZ(H)B / NXZ(H)M catalogue. The exact version (S or H, A or B controller) is shown on the product label – please confirm before ordering.Key functions
- Automatic transfer – on phase loss, undervoltage or overvoltage.
- Overload and short-circuit protection – NXM circuit breakers, Icn 50 kA.
- Three modes – grid–grid with or without return, grid–generator.
- Manual operation and position 0 – both sources disconnected for maintenance.
- Fault indication, fire-control input, RS485 – depending on the controller type.
How does it differ from similar switches?
- CHINT NXZM-400S/3 400 A – lower rated current – 400 A.
- CHINT NXZM-800S/3 800 A – higher rated current – 800 A.
- CHINT NXZ (PC class) – no built-in protection, circuit breakers or fuses are needed upstream.
- Modular DIN ATS up to 125 A – for homes and small sites; CHINT NXZM – for switchboards and higher currents.
Where is it used?
- Main switchboards of industrial and commercial buildings – dual supply backup.
- Sites with a backup generator – factories, warehouses, farms.
- Hospitals, server rooms, telecom nodes – where a power interruption is costly.
- High-rise buildings – supply of fire safety systems, fire-control input.
- Residential houses – three-phase supply with a generator.
Use by need
For switchboard builders.
A factory-made ATS with controller – less mounting and commissioning.For power engineers.
Dual supply or grid–generator backup with adjustable limits and delays.For building owners.
Power is restored automatically – without human intervention.Practical use
Example: a site supply up to 630 A and a backup generator. The ATS is mounted in the switchboard between the supply and load busbars, the controller is set to grid–generator mode and the generator remote start input is connected to contact 601–603 of the B type controller. When the grid fails the generator starts, and the load is transferred only when its voltage reaches the set limits.
Advantages
- Built-in protection – Icn 50 kA (S type).
- Adjustable voltage limits and delays.
- Three operating modes – for grid and generator.
- Factory-made CHINT solution – drive and controller in one.
- Mechanical endurance – 4 000 cycles.
Disadvantages / limitations
- Generator control only with the B type controller.
- There is a short interruption during transfer – this is not a UPS.
- Larger than modular ATS – needs switchboard space.
- The controller needs a correctly connected N – a mistake can damage it.
Safety and installation notes
- Before work, disconnect both sources and switch the controller to manual mode – the ATS can transfer automatically.
- Phase sequence and N – the manufacturer warns that a wrongly connected N can burn the controller.
- Sources are connected at the top, the load at the bottom; vertical or horizontal mounting.
- Select cables and busbars for 630 A and the manufacturer's terminal dimensions.
- Installation by a qualified electrician; the generator N–PE bond according to the site earthing system.
Quick selection guide
Choose CHINT NXZM-630S/3 if the supply is up to 630 A, the system is 400/415 V and you need an ATS with built-in short-circuit protection.
3P · 630 A400/415 VCB · IEC 60947-6-1AC-33BSuitable when you need:- dual supply or grid–generator backup up to 630 A;
- a three-phase 400/415 V system;
- short-circuit protection in the ATS itself.
Check before use:- the number of poles – 3P or 4P (N switching);
- the controller type – a generator needs B;
- switchboard space and cable cross-section for 630 A.
Important: An ATS does not replace a design – the number of poles, protection and generator connection are confirmed by the designer.FAQ
Can CHINT NXZM-630S/3 start a generator?
Yes, if a B type (intelligent) controller is ordered – contact 601–603 closes when the main source fails. The A type controller does not control a generator.How long does the transfer take?
The operating transfer time of the mechanism is 3.5 s ±10 %, plus the set delay (0–180 s).Is protection needed upstream of the ATS?
A CB class ATS already has NXM circuit breakers (Icn 50 kA). Selectivity with the supply protection is confirmed by the designer.What voltage limits can be set?
Undervoltage – 160–200 V (default 187 V), overvoltage – 240–290 V (default 263 V).3P or 4P?
NXZM-630S/3 is the 3P version: N is not switched and an external N wire is connected to the controller. If the generator N is bonded to PE, choose the 4P version.Can it be controlled remotely?
The B type controller has an RS485 (Modbus) interface – status and parameters can be sent to the building management system.Automatic transfer switch ATS CHINT NXZM-630S/3 | 3P | 630 A | 400/415 V | CB class
CHINT NXZM-630S/3 – CB class 3P automatic transfer switch 630 A for 400/415 V systems with two sources: built-in protection, adjustable voltage limits, delays and three operating modes.
Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.This product is marked with the CE label, which confirms that it complies with all applicable European Union directives and regulations. CE marking is not just a formality – it is an important indicator of quality and safety, ensuring that the product has been properly assessed, tested, and can be safely used throughout the EU market.
CE certification means that the product has been evaluated according to the main criteria:
Safety requirements – ensures that the product does not pose a risk to the user or the environment
Electromagnetic compatibility (EMC) – the device does not interfere with other equipment and is resistant to external disturbances
Environmental standards – complies with current ecological and material usage requirements
Operational reliability – the product is suitable for long-term use according to its intended purposeCE marking allows this product to:
be legally supplied and used in all European Union countries
ensure a high level of quality and safety
be used in residential, commercial, and industrial environmentsThe CE mark is a declaration of the manufacturer’s responsibility, confirming that the product complies with all applicable standards and has been assessed according to EU legislation.
What does this mean for you as a buyer?
Safe use in everyday activities
Reliable performance and reduced risk of failure
Compliance with EU standards and requirements
Suitability for professional solutions
Love it? Share your thoughts in a review!Write Review Alternative products
U-FTP Cable | 6A CAT | 4x2x23 AWG | shielded | copper | UV resistant | outdoor use | blackCode: KIF6AOUTS500The U/FTP cable is a high-quality four-pair data transmission cable designed for telecommunication, industrial, and outdoor network installations. This cable is 100% copper, ensuring maximum signal transmission efficiency and minimal signal attenuation.
It is adapted for 10 Gigabit Ethernet (10GBASE-T) data transmission at speeds of up to 10,000 Mbps and provides high electromagnetic resistance, as each pair is shielded with aluminum foil. Thanks to the PE outer layer, the cable is resistant to moisture, UV radiation, and mechanical impact, making it ideal for outdoor installations.
Price 0.73 € VAT incl.( 0.60 € VAT excl. )Network plug | RJ45 connector (8P8C) | for UTP CAT 6e cable | unshielded | through-plug | transparentCode: WT117This RJ45 Cat.6 UTP modular plug is a high-quality 8P8C unshielded network connector type, designed for Cat.6 UTP (Unshielded Twisted Pair) cables. The special straight-through design makes cable termination easier and more convenient, as the wires can be threaded through the plug, allowing a visual check of the wire arrangement before crimping the connector.
Price 0.20 € VAT incl.( 0.17 € VAT excl. )Solar PV cable | H1Z2Z2-K | 1x4 mm² | black | 1.5 kV DC | EN 50618 | Dca | IEMMEQU HARCode: H1Z2Z2KThe cable is designed for connecting photovoltaic (solar energy) systems and interconnecting solar modules. This cable offers excellent resistance to ultraviolet (UV) rays, ozone, atmospheric effects, and temperature fluctuations. A durable and flexible single-core copper cable with double insulation ensures long service life and safe use even in the most challenging outdoor conditions. Suitable for installation both indoors and outdoors.
Price 0.98 € VAT incl.( 0.81 € VAT excl. )






















