Products catalog

  • Automatic transfer switch ATS TAXNELE TXATS2 | 2P | 63 A | with handle

    Code: ESTXATS2-63-2P
    Price 29.04 € VAT incl.
    ( 24.00 € VAT excl. )
    Buy more, pay less
    10+ pcs.  – 13.55 € for pcs. -53%

    TAXNELE TXATS2 2P 63 A – automatic transfer switch with manual handle. Transfer up to 4 s, priority to the main source.

  • Automatic transfer switch ATS TAXNELE TXATS2 | 2P | 63 A | with handle

    TAXNELE TXATS2 is an automatic transfer switch (ATS) with motor drive and manual handle. Main source – N (Normal Power), backup – R (Emergency Power). 2P, 63 A.

    Key point
    A simple, clear solution for a house or small site: automatic mode transfers by itself, in manual mode the direction is changed with the handle. Transfer up to 4 s with interruption.
    Poles / current
    2P / 63 A
    Class
    MCB type
    Transfer
    < 4 s
    Control
    Auto / manual

    How it works

    Main source – N, backup – R. In automatic mode, when N fails and R is energised, the switch transfers to R and returns to N when it is restored.

    The manufacturer states that only phase A voltage is monitored and loss of voltage or phase is detected. Transfer up to 4 s with a short interruption.

    The red switch on top selects Automatic / Manual. In manual mode the direction is changed with the blue "Direction" handle.

    Technical specifications

    Type Automatic transfer switch (ATS) with drive and handle
    Manufacturer TAXNELE (Taixin Electric), series TXATS2
    Poles 2P
    Rated current 63 A
    Operating voltage 200–240 V AC
    Frequency 50/60 Hz
    Transfer time < 4 s – with supply interruption
    Control Automatic / Manual, "Direction" handle
    Monitored Phase A voltage of both sources
    Mounting On mounting plate, through bracket holes
    Standard IEC 60947-6-1, GB/T 14048.11
    Data source Manufacturer nameplate and manufacturer technical information
    ⚠ The brand on the device is TAXNELE. The table lists only parameters stated by the manufacturer; parameters not provided by the manufacturer are not listed. Photos may show another current or pole version of the same series – check exact data on the device nameplate. Ui and Uimp are not specified by the manufacturer.

    Functions

    • Automatic transfer N → R and back
    • Priority to main source N
    • Automatic / Manual switch
    • Manual operation with "Direction" handle
    • Source indication

    Other versions of the same series

    • TAXNELE TXATS2 4P 63 A
    • 2P – single-phase site, 4P – three-phase with N.
    • If transfer without interruption is required, choose PC class TXATS.

    Applications

    • Houses and homesteads with a generator
    • Small sites where a short interruption is acceptable
    • Temporary sites and construction sites

    Practical example

    House with a generator: grid – N, generator – R. When the grid fails and the generator is started, the ATS transfers to R. A few seconds' interruption does not harm fridges or a boiler.

    Advantages

    • Simple operation
    • Manual operation without tools
    • Priority to the main source

    Points to note

    • Transfer up to 4 s with interruption
    • Only phase A monitored
    • No generator start control

    ⚡ Safe installation

    • Installation must be carried out by a qualified electrician with both sources disconnected.
    • Install short-circuit and overload protection upstream of the ATS on both supplies.
    • Select cable cross-section for 63 A and the installation conditions.
    • Connect a generator to the house installation only through a transfer switch – never through a socket outlet.
    ☝ Elsprendimai.eu recommends: ATS selection guide · Diagrams: 3P or 4P · Consultation

    How to choose

    Poles – by the network, current – not lower than the incoming protection current. Consider whether an interruption of up to 4 s is acceptable.

    2P · 63 A
    200–240 V AC
    MCB type
    < 4 s
    Suitable if:
    • a few seconds' interruption is acceptable
    • simple operation is required
    Check:
    • Ue: 2P – 200–240 V, 4P – 350–440 V
    • whether a phase monitoring relay is needed
    Important: A transfer switch is not a protective device (except CB class) – install short-circuit and overload protection separately. If in doubt, consult a qualified electrician.

    Frequently asked questions

    Is the transfer without interruption?
    No, transfer up to 4 s with supply interruption.
    Are all phases monitored?
    No, only phase A (manufacturer data).
    Does it start the generator?
    No. The manufacturer states that the switch cannot turn the generator on or off.
    How to switch manually?
    Set the switch to Manual and turn the blue handle.
    Can you help with selection?
    Yes. Send us the network type, incoming protection and generator power – we will help you choose the right switch.

    Automatic transfer switch ATS TAXNELE TXATS2 | 2P | 63 A | with handle

    Simple ATS with handle – where a short interruption is acceptable and clear operation matters.

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • Alternative products

    U-FTP Cable | 6A CAT | 4x2x23 AWG | shielded | copper | UV resistant | outdoor use | black
    Code: KIF6AOUTS500

    The U/FTP cable is a high-quality four-pair data transmission cable designed for telecommunication, industrial, and outdoor network installations. This cable is 100% copper, ensuring maximum signal transmission efficiency and minimal signal attenuation.

    It is adapted for 10 Gigabit Ethernet (10GBASE-T) data transmission at speeds of up to 10,000 Mbps and provides high electromagnetic resistance, as each pair is shielded with aluminum foil. Thanks to the PE outer layer, the cable is resistant to moisture, UV radiation, and mechanical impact, making it ideal for outdoor installations. 

    Price 0.73 € VAT incl.
    ( 0.60 € VAT excl. )
    Network plug | RJ45 connector (8P8C) | for UTP CAT 6e cable | unshielded | through-plug | transparent
    Code: WT117

    This RJ45 Cat.6 UTP modular plug is a high-quality 8P8C unshielded network connector type, designed for Cat.6 UTP (Unshielded Twisted Pair) cables. The special straight-through design makes cable termination easier and more convenient, as the wires can be threaded through the plug, allowing a visual check of the wire arrangement before crimping the connector.

    Price 0.20 € VAT incl.
    ( 0.17 € VAT excl. )
    Solar PV cable | H1Z2Z2-K | 1x4 mm² | black | 1.5 kV DC | EN 50618 | Dca | IEMMEQU HAR
    Code: H1Z2Z2K

    The cable is designed for connecting photovoltaic (solar energy) systems and interconnecting solar modules. This cable offers excellent resistance to ultraviolet (UV) rays, ozone, atmospheric effects, and temperature fluctuations. A durable and flexible single-core copper cable with double insulation ensures long service life and safe use even in the most challenging outdoor conditions. Suitable for installation both indoors and outdoors.

    Price 0.98 € VAT incl.
    ( 0.81 € VAT excl. )
  • privacy policy

    Information