Products catalog

  • Automatic transfer switch for solar PV ATS TAXNELE TXATS-PV | inverter–grid | 4P | 63 A | DIN

    Code: ESTXATS-63PV-4P
    Price 76.98 € VAT incl.
    ( 63.62 € VAT excl. )
    Buy more, pay less
    10+ pcs.  – 25.41 € for pcs. -66%

    TAXNELE TXATS-PV 4P 63 A – automatic transfer switch for solar PV: inverter on side A, grid on side B. PC class, DIN mounting.

  • Automatic transfer switch for solar PV ATS TAXNELE TXATS-PV | inverter–grid | 4P | 63 A | DIN

    TAXNELE TXATS-PV is an automatic transfer switch for systems where the main source is a solar PV inverter (A) and the backup is the grid (B). 4P, 63 A, DIN rail mounting.

    Key point
    This version is only for an inverter + grid scheme. The manufacturer states: inverter on side A, grid on side B, and side B must be energised at all times. For a generator use the standard TXATS.
    Poles / current
    4P / 63 A
    Class
    PC
    Transfer
    < 8 ms
    Control
    Auto / manual

    How it works

    Side A – inverter (solar PV), side B – grid. While the inverter supplies voltage, the load is fed from it. If the inverter voltage is lost, the load is transferred to the grid and returned when the inverter recovers.

    The manufacturer stresses that side B (grid) must be energised at all times because the inverter voltage is not stable. This version is not suitable for a grid + generator scheme.

    The Manual / Auto switch selects the mode; the handle is used only in "Manual" mode. Control terminals AR, AN and passive NC–C–NO contacts – as in the standard TXATS.

    Technical specifications

    Type Automatic transfer switch for inverter and grid (ATS), PC class
    Manufacturer TAXNELE (Taixin Electric), series TXATS-PV
    Poles 4P
    Rated current 63 A
    Operating voltage 220–240 V AC (L–N)
    Frequency 50/60 Hz
    Insulation voltage Ui AC 690 V
    Impulse voltage Uimp 8 kV
    ATSE class PC (IEC 60947-6-1)
    Transfer time < 8 ms – without supply interruption (PC class)
    Control Auto / Manual; handle in Manual mode only
    Additional terminals AR, AN / BR, BN – monitoring; NC–C–NO – passive contacts
    Mounting 35 mm DIN rail
    Standard IEC 60947-6-1
    Data source Manufacturer nameplate and manufacturer technical information
    ⚠ The brand on the device is TAXNELE. The table lists only parameters stated by the manufacturer; parameters not provided by the manufacturer are not listed. Photos may show another current or pole version of the same series – check exact data on the device nameplate. Not suitable for a grid + generator scheme.

    Functions

    • Automatic transfer inverter → grid and back
    • Priority to inverter (A)
    • Mechanical interlock between A and B
    • Manual operation in Manual mode
    • A and B indicators
    • Passive NC–C–NO contacts

    Other versions of the same series

    Applications

    • Solar PV systems with the inverter as the main source
    • Houses where the inverter feeds the loads and the grid is backup
    • Hybrid systems with batteries

    Practical example

    House with a hybrid inverter: inverter AC output to A, grid to B. While the inverter supplies voltage, the house is fed from it; if the inverter switches off – from the grid. Side B must always be energised.

    Advantages

    • Designed for an inverter and grid scheme
    • PC class, transfer without interruption
    • Ui 690 V, Uimp 8 kV
    • DIN mounting

    Points to note

    • Only for inverter and grid – not for a generator
    • Side B (grid) must be energised at all times
    • Does not break short circuits – protection required

    ⚡ Safe installation

    • Installation must be carried out by a qualified electrician with both sources disconnected.
    • Install short-circuit and overload protection upstream of the ATS on both supplies.
    • Select cable cross-section for 63 A and the installation conditions.
    • Connect a generator to the house installation only through a transfer switch – never through a socket outlet.
    • Connect the inverter to A and the grid to B – not the other way round.
    ☝ Elsprendimai.eu recommends: ATS selection guide · Diagrams: 3P or 4P · Consultation

    How to choose

    Check that the main source really is the inverter and the grid is backup. Poles – by the number of inverter phases, current – by the inverter output and incoming protection.

    4P · 63 A
    220–240 V AC (L–N)
    PC · IEC 60947-6-1
    < 8 ms
    Suitable if:
    • the main source is an inverter
    • the grid is always available as backup
    • inverter output is not higher than 63 A
    Check:
    • that the inverter is connected to A
    • that the grid (B) is always energised
    • number of poles
    Important: A transfer switch is not a protective device (except CB class) – install short-circuit and overload protection separately. If in doubt, consult a qualified electrician.

    Frequently asked questions

    Can it be used with a generator?
    No. The manufacturer states that the PV version is only for an inverter and grid. For a generator choose the standard TXATS.
    Why must the grid be on side B?
    The manufacturer states that the inverter voltage is not stable, so it is connected to A, and the stable grid to B, which must be energised at all times.
    Is the transfer without interruption?
    Yes, PC class, manufacturer-stated transfer time under 8 ms.
    Does this ATS control the inverter?
    No, it only transfers the load between sources.
    Can you help with selection?
    Yes. Send us the network type, incoming protection and generator power – we will help you choose the right switch.

    Automatic transfer switch for solar PV ATS TAXNELE TXATS-PV | inverter–grid | 4P | 63 A | DIN

    ATS for an inverter and grid scheme: inverter as main source, grid as backup. PC class, transfer without interruption.

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • Alternative products

    Network plug | RJ45 connector (8P8C) | for UTP CAT 6e cable | unshielded | through-plug | transparent
    Code: WT117

    This RJ45 Cat.6 UTP modular plug is a high-quality 8P8C unshielded network connector type, designed for Cat.6 UTP (Unshielded Twisted Pair) cables. The special straight-through design makes cable termination easier and more convenient, as the wires can be threaded through the plug, allowing a visual check of the wire arrangement before crimping the connector.

    Price 0.20 € VAT incl.
    ( 0.17 € VAT excl. )
    U-FTP Cable | 6A CAT | 4x2x23 AWG | shielded | copper | UV resistant | outdoor use | black
    Code: KIF6AOUTS500

    The U/FTP cable is a high-quality four-pair data transmission cable designed for telecommunication, industrial, and outdoor network installations. This cable is 100% copper, ensuring maximum signal transmission efficiency and minimal signal attenuation.

    It is adapted for 10 Gigabit Ethernet (10GBASE-T) data transmission at speeds of up to 10,000 Mbps and provides high electromagnetic resistance, as each pair is shielded with aluminum foil. Thanks to the PE outer layer, the cable is resistant to moisture, UV radiation, and mechanical impact, making it ideal for outdoor installations. 

    Price 0.73 € VAT incl.
    ( 0.60 € VAT excl. )
    Solar PV cable | H1Z2Z2-K | 1x4 mm² | black | 1.5 kV DC | EN 50618 | Dca | IEMMEQU HAR
    Code: H1Z2Z2K

    The cable is designed for connecting photovoltaic (solar energy) systems and interconnecting solar modules. This cable offers excellent resistance to ultraviolet (UV) rays, ozone, atmospheric effects, and temperature fluctuations. A durable and flexible single-core copper cable with double insulation ensures long service life and safe use even in the most challenging outdoor conditions. Suitable for installation both indoors and outdoors.

    Price 0.98 € VAT incl.
    ( 0.81 € VAT excl. )
  • privacy policy

    Information