Products catalog

Home/Product Catalog/Electrical distribution and installation/Electrical Energy Supply | Distribution Panels | Boxes | Accessories/Sealing products | seals for electrical wires | cables | panels | boxes
  • New item   Membrane cable entry plate | for 138×48 mm cut-out | 2× Ø12–21 + 2× Ø8–15 + 6× Ø5–8 mm | grey | IP55 | HT Hi Tech Polymers | HTB-10
    New item   Membrane cable entry plate | for 138×48 mm cut-out | 2× Ø12–21 + 2× Ø8–15 + 6× Ø5–8 mm | grey | IP55 | HT Hi Tech Polymers | HTB-10 1

    Membrane cable entry plate | for 138×48 mm cut-out | 2× Ø12–21 + 2× Ø8–15 + 6× Ø5–8 mm | grey | IP55 | HT Hi Tech Polymers | HTB-10

    Code: Sandariklis HTB-10
    Inquire about this item
    Price 4.71 € VAT incl.
    ( 3.89 € VAT excl. )
    Want another price? Suggest yours!

    HTB-10 is a compact membrane cable entry plate for a smaller 138 × 48 mm (B-hole) cut-out. It has 10 entries: 2 × Ø12–21 mm, 2 × Ø8–15 mm and 6 × Ø5–8 mm. IP55, −40…+130 °C, fixed through Ø7.5 mm holes.

  • Product description

    Membrane cable entry plate | for 138×48 mm cut-out | 2× Ø12–21 + 2× Ø8–15 + 6× Ø5–8 mm | grey | IP55 | HT Hi Tech Polymers | HTB-10

    HTB-10 is a compact membrane cable entry plate for a smaller 138 × 48 mm (B-hole) cut-out, for when a 216 × 84 mm plate does not fit the enclosure or is not needed. It has 10 entries: two Ø12–21 mm for supply cables, two Ø8–15 mm, and six Ø5–8 mm for control and signal lines.

    Key point:
    Small control and junction boxes usually have up to ten cables and little space on the bottom or side. HTB-10 takes that many cables through one small cut-out, so you do not have to drill several holes for separate glands in the wall of a small enclosure.
    Entries
    10
    Cable Ø
    5–21 mm
    Protection
    IP55
    Cut-out
    138 × 48 mm

    How it works

    Installation: a 138 × 48 mm cut-out and Ø7.5 mm fixing holes (spacing 120 / 30 mm) are made in the enclosure, and the plate is fixed with screws.

    Operation: the required membrane is cut slightly smaller than the cable outer Ø, the cable is pushed through and the TPE seals tightly around it.

    Result: up to 10 cables through one small cut-out, IP55 sealing, and unused entries stay closed.

    Why choose HTB-10?
    HTB-10 brings the convenience of a multi-entry plate to small enclosures: one 138 × 48 mm cut-out instead of several holes and glands. The two larger Ø12–21 mm entries suit a supply cable, and the six small ones take sensors, push-buttons or communication lines.

    Technical specifications

    Product type Membrane cable entry plate (compact)
    Code HTB-10
    Manufacturer HT Hi Tech Polymers Oy (Finland)
    Openings and cable Ø 2 × Ø12–21 mm; 2 × Ø8–15 mm; 6 × Ø5–8 mm
    Max. number of cables 10
    Enclosure cut-out 138 × 48 mm (B-hole, FL13)
    Fixing holes Ø7.5 mm, spacing 120 / 30 mm
    Degree of protection IP55 (EN 60529)
    Operating temperature −40…+130 °C
    Material TPE-SEBS, 50 ShA, halogen-free
    Properties resistant to oil splashes; for indoor and outdoor use
    Colour grey (RAL7035)

    Main functions

    • 2 entries Ø12–21 mm – for supply or larger cables
    • 2 entries Ø8–15 mm – for medium-size lines
    • 6 entries Ø5–8 mm – for thin control, sensor and communication lines
    • Compact B-hole 138 × 48 mm – suits smaller enclosures
    • IP55 – protection against dust and water jets (EN 60529)
    • Halogen-free TPE-SEBS – −40…+130 °C, indoor and outdoor

    Where is it used?

    • Small automation and control boxes
    • Gate, barrier and door automation controllers
    • Ventilation, heating and heat recovery control boxes
    • Junction boxes at machines and equipment
    • Irrigation and outdoor equipment control boxes
    • Low-voltage and communication distribution boxes
    • Solar and sensor junction boxes

    Use by need

    For small automation enclosure builders.
    One small cut-out instead of several holes – faster enclosure preparation and a tidy entry.
    For electricians and automation installers.
    Cables go in without gland nuts: cut the membrane, push the cable through, secure it inside.
    For equipment service technicians.
    When a sensor or push-button is added, a free entry is already there – no drilling of the box.

    Practical use

    If a gate automation control box needs a supply cable, a motor cable, and lines for photocells, a warning lamp and push-buttons, HTB-10 takes all of them through one 138 × 48 mm cut-out.

    Pros

    • Up to 10 cables through one small cut-out
    • Three entry sizes – from Ø5 to Ø21 mm
    • Suits enclosures where a 216 × 84 mm plate does not fit
    • Unopened entries stay closed
    • −40…+130 °C, halogen-free, indoor and outdoor

    Cons / limitations

    • IP55, not IP65 – where a dust-tight entry is needed choose an IP65 plate (e.g. HTC-25 for a 216 × 84 mm cut-out)
    • Largest entry Ø21 mm – thicker cables need a 216 × 84 mm plate, e.g. HTC-35
    • The membrane does not provide strain relief – secure cables inside the box
    • Not a fire barrier

    Safety and installation notes

    • Make the cut-out with the power off or before equipment is installed in the box.
    • After cutting, remove burrs and swarf – in a small enclosure they easily reach the terminals.
    • Cut the membrane slightly smaller than the cable outer Ø; one cable per entry.
    • Secure cables inside the box so that pulling does not act on the membrane.
    • Fix the plate evenly against a flat surface through the Ø7.5 mm holes.

    Quick selection guide

    2 × Ø12–21 mm
    2 × Ø8–15 mm
    6 × Ø5–8 mm
    Cut-out 138 × 48 mm
    Suitable when you need:
    • up to 10 cables into a small box
    • a compact 138 × 48 mm cut-out
    • spare entries for sensors or push-buttons
    Check before use:
    • the cable outer Ø – does it fit 5–8, 8–15 or 12–21 mm
    • whether IP55 is enough for your environment
    • whether the enclosure can take a 138 × 48 mm cut-out and Ø7.5 mm holes (120 / 30 mm)
    Important reminder: HTB-10 seals the cable entry to IP55, but it does not provide strain relief and is not a fire barrier – secure the cables inside.

    FAQ

    What cut-out is HTB-10 for?
    A 138 × 48 mm B-hole with Ø7.5 mm fixing holes, spacing 120 / 30 mm.
    How many cables can be installed?
    Up to 10: 2 × Ø12–21 mm, 2 × Ø8–15 mm and 6 × Ø5–8 mm.
    What is the degree of protection of HTB-10?
    The manufacturer specifies IP55.
    Does HTB-10 fit a 216 × 84 mm cut-out?
    No, it is a smaller plate; for a 216 × 84 mm cut-out choose the HTC series, e.g. HTC-25.
    Can it be used outdoors?
    Yes, the manufacturer specifies indoor and outdoor use, −40…+130 °C.
    Do unused entries need to be closed?
    No, unopened membranes stay closed.

    Manufacturer documents

    Links open on external websites. Checked 2026-10-04. If data differ, the latest manufacturer edition applies – or contact us.

    HTB-10 compact plate for 138 × 48 mm cut-out

    HTB-10 is an IP55 membrane cable entry plate for a 138 × 48 mm cut-out: 2 × Ø12–21, 2 × Ø8–15 and 6 × Ø5–8 mm entries, up to 10 cables in small enclosures.

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.

  • Alternative products

  • Subscribtion to new arrivals

    privacy policy

    Information