Products catalog

  • Automatic Transfer Switch ATS RP6-63L/4P | 4P | 63 A | 400 V | CB class | display and buttons

    Code: ES-RP6-63L/4P
    Price 124.03 € VAT incl.
    ( 102.50 € VAT excl. )
    Buy more, pay less
    10+ pcs.  – 69.45 € for pcs. -44%

    RP6-63L/4P – CB-class automatic transfer switch 4P 63 A 400 V with display, control buttons and handle for manual transfer. Panel (plate) mounting.

  • Automatic Transfer Switch ATS RP6-63L/4P | 4P | 63 A | 400 V | CB class | display and buttons

    RP6-63L/4P is a CB-class automatic transfer switch (ATS) for two sources: main (I) and backup (II). It consists of two four-pole switching modules with a controller and display in the middle. Three phases and N are switched.

    Key point
    Per the label: 63 A, 400 V, 50 Hz, CB class, standard IEC 60947-6-1. A CB-class switch is built from switching modules; positions are I, OFF and II.
    Poles / current
    4P / 63 A
    Voltage
    400 V, 50 Hz
    Class
    CB
    Control
    Auto / Manu, I, OFF, II

    How it works

    The main source connects to the left module (I), the backup to the right (II), the load to the output terminals. The controller monitors source voltage.

    In automatic mode, when main source voltage is lost, the controller transfers the load to the backup and returns it when the main source is restored.

    Buttons Auto/Manu, I, OFF and II select the mode and position; manual transfer is also possible with the handle. The display shows source status and over-voltage (OV) and under-voltage (UV) signals.

    Technical specifications

    Type Automatic transfer switch (ATS)
    Model RP6-63L/4P
    Poles 4P
    Rated current 63 A
    Rated voltage 400 V
    Frequency 50 Hz
    Class CB
    Standard IEC 60947-6-1
    Positions I – OFF – II
    Control Buttons Auto/Manu, I, OFF, II; handle
    Indication Display, source status, OV / UV
    Dimensions 258 × 125 × 111 mm (mounting hole spacing 230 mm)
    Mounting On mounting plate (screws)
    Data source Manufacturer label and dimension drawing in product photos
    ⚠ The manufacturer is not stated on the product. The table lists only parameters visible on the label and drawing. Transfer time, Ui, Uimp and short-circuit ratings are not legible – verify before installation.

    Functions

    • Automatic transfer I → II and return
    • Auto / Manu modes
    • Positions I, OFF, II
    • Manual transfer with handle
    • Display and OV / UV indication

    Applications

    • Three-phase homes and farms with a generator
    • Small commercial sites
    • Panels with a second supply

    Practical example

    A three-phase house with a 3 × 40 A supply and a three-phase generator: grid to I, generator to II, load panel to the output. Circuit breakers before the switch on both supplies.

    Advantages

    • CB class, 4P
    • Display and control buttons
    • OFF position – both sources disconnected
    • Manual transfer with handle

    Points to note

    • Manufacturer not stated
    • Transfer time not stated
    • Not DIN – plate mounted
    • No generator start control on the label

    ⚡ Safe installation

    • Installation must be carried out by a qualified electrician with both sources disconnected.
    • Install short-circuit and overload protection upstream of the switch on both supplies.
    • Connect a generator to the house installation only through a transfer switch – never through a socket outlet.
    • Leave room for the display and handle – product depth is 111 mm.
    ☝ Elsprendimai.eu recommends: ATS selection guide · Diagrams: 3P or 4P · Consultation

    How to choose

    Suitable for a three-phase 400 V site up to 63 A when the panel has room for a 258 mm wide device on a mounting plate.

    Suitable if:
    • site is three-phase 400 V
    • load current up to 63 A
    • you want status on a display
    Check:
    • panel depth (111 mm)
    • incoming protection before the switch
    • how the generator is started
    Important: Always check exact parameters on the device nameplate and in the manufacturer's instructions. If in doubt, consult a qualified electrician.

    Frequently asked questions

    Does the switch start the generator?
    No such function on the label – the generator start is handled by its own controller.
    What does the OFF position mean?
    Both sources are disconnected from the load – useful for maintenance.
    Is it DIN-rail mounted?
    No, it is screwed onto a mounting plate (hole spacing 230 mm).
    Can you help with selection?
    Yes. Send us the network type, incoming protection and generator power – we will help you choose the right solution.

    Automatic Transfer Switch ATS RP6-63L/4P | 4P | 63 A | 400 V | CB class | display and buttons

    RP6-63L/4P – CB-class 4P 63 A 400 V ATS with display, control buttons and handle.

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • Alternative products

    U-FTP Cable | 6A CAT | 4x2x23 AWG | shielded | copper | UV resistant | outdoor use | black
    Code: KIF6AOUTS500

    The U/FTP cable is a high-quality four-pair data transmission cable designed for telecommunication, industrial, and outdoor network installations. This cable is 100% copper, ensuring maximum signal transmission efficiency and minimal signal attenuation.

    It is adapted for 10 Gigabit Ethernet (10GBASE-T) data transmission at speeds of up to 10,000 Mbps and provides high electromagnetic resistance, as each pair is shielded with aluminum foil. Thanks to the PE outer layer, the cable is resistant to moisture, UV radiation, and mechanical impact, making it ideal for outdoor installations. 

    Price 0.73 € VAT incl.
    ( 0.60 € VAT excl. )
    Solar PV cable | H1Z2Z2-K | 1x4 mm² | black | 1.5 kV DC | EN 50618 | Dca | IEMMEQU HAR
    Code: H1Z2Z2K

    The cable is designed for connecting photovoltaic (solar energy) systems and interconnecting solar modules. This cable offers excellent resistance to ultraviolet (UV) rays, ozone, atmospheric effects, and temperature fluctuations. A durable and flexible single-core copper cable with double insulation ensures long service life and safe use even in the most challenging outdoor conditions. Suitable for installation both indoors and outdoors.

    Price 0.98 € VAT incl.
    ( 0.81 € VAT excl. )
    Network plug | RJ45 connector (8P8C) | for UTP CAT 6e cable | unshielded | through-plug | transparent
    Code: WT117

    This RJ45 Cat.6 UTP modular plug is a high-quality 8P8C unshielded network connector type, designed for Cat.6 UTP (Unshielded Twisted Pair) cables. The special straight-through design makes cable termination easier and more convenient, as the wires can be threaded through the plug, allowing a visual check of the wire arrangement before crimping the connector.

    Price 0.20 € VAT incl.
    ( 0.17 € VAT excl. )
  • privacy policy

    Information