Products catalog

  • Automatic transfer switch ATS TAXNELE TXATS1 | 4P | 125 A | CB class

    Code: ESTXATS1-125-4P
    Price 110.35 € VAT incl.
    ( 91.20 € VAT excl. )
    Buy more, pay less
    10+ pcs.  – 42.02 € for pcs. -61%

    TAXNELE TXATS1 4P 125 A – automatic transfer switch with circuit breaker modules. CB class, Icn 5 kA, transfer up to 4 s.

  • Automatic transfer switch ATS TAXNELE TXATS1 | 4P | 125 A | CB class

    TAXNELE TXATS1 is an automatic transfer switch (ATS) made of two motor-driven circuit breaker modules. Main source – N (Normal), backup – R (Reserve). 4P, 125 A.

    Key point
    CB class means the switch includes circuit breaker function (nameplate: Icm 7.65 kA, Icn 5 kA). Transfer takes up to 4 s with a short supply interruption.
    Poles / current
    4P / 125 A
    Class
    CB
    Transfer
    < 4 s
    Control
    Auto / manual

    How it works

    The normal source side is marked N, the reserve side R. In automatic mode, when N voltage (or a phase) is lost and R is energised, the drive opens the N module and closes R. When N returns, it transfers back.

    The manufacturer states that only phase A voltage of both sources is monitored and only loss of voltage or phase is detected. Transfer takes up to 4 s and the load is unsupplied during that time.

    The handle has three positions N–0–R. The Auto / Manual mode switch is on top, next to the "Un N on" and "Ur R on" indicators.

    Technical specifications

    Type Automatic transfer switch with circuit breaker modules, CB class
    Manufacturer TAXNELE (Taixin Electric), series TXATS1
    Poles 4P
    Rated current 125 A
    Operating voltage 350–440 V AC
    Frequency 50/60 Hz
    Insulation voltage Ui AC 400 V
    Impulse voltage Uimp 4 kV
    ATSE class CB (IEC 60947-6-1)
    Making capacity Icm 7.65 kA
    Breaking capacity Icn 5 kA
    Transfer time < 4 s – with supply interruption
    Control Auto / Manual, handle N–0–R
    Monitored Phase A voltage of both sources
    Mounting On mounting plate, through bracket holes
    Standard IEC/EN 60947-6-1
    Data source Manufacturer nameplate and manufacturer technical information
    ⚠ The brand on the device is TAXNELE. The table lists only parameters stated by the manufacturer; parameters not provided by the manufacturer are not listed. Photos may show another current or pole version of the same series – check exact data on the device nameplate. Ue 2P – 200–240 V AC, 4P – 350–440 V AC (manufacturer data).

    Functions

    • Automatic transfer N → R and back
    • Circuit breaker function (CB class)
    • N–0–R handle with 0 position
    • Auto / Manual switch
    • Un N on / Ur R on indication

    Other versions of the same series

    Applications

    • Houses and homesteads with a generator
    • Farms and workshops
    • Sites where a short interruption during transfer is acceptable

    Practical example

    Farm with a three-phase generator: grid – side N, generator – R. When the grid fails, the ATS transfers to the generator within a few seconds. As only phase A is monitored, a phase monitoring relay is worth adding for three-phase motors.

    Advantages

    • Circuit breaker function, Icn 5 kA
    • Handle with 0 position
    • Clearly marked N and R sides

    Points to note

    • Transfer up to 4 s with interruption
    • Only phase A monitored
    • No generator start control
    • Icn 5 kA – check the short-circuit current

    ⚡ Safe installation

    • Installation must be carried out by a qualified electrician with both sources disconnected.
    • Install short-circuit and overload protection upstream of the ATS on both supplies.
    • Select cable cross-section for 125 A and the installation conditions.
    • Connect a generator to the house installation only through a transfer switch – never through a socket outlet.
    • Check that the short-circuit current at the installation point does not exceed 5 kA.
    ☝ Elsprendimai.eu recommends: ATS selection guide · Diagrams: 3P or 4P · Consultation

    How to choose

    Poles – by the network, current – not lower than the incoming protection current. Consider whether an interruption of up to 4 s is acceptable.

    4P · 125 A
    350–440 V AC
    CB · IEC 60947-6-1
    < 4 s
    Suitable if:
    • a few seconds' interruption is acceptable
    • CB class function is required
    • short-circuit current does not exceed 5 kA
    Check:
    • Ue: 2P – 200–240 V, 4P – 350–440 V
    • short-circuit current
    • whether a phase monitoring relay is needed
    Important: A transfer switch is not a protective device (except CB class) – install short-circuit and overload protection separately. If in doubt, consult a qualified electrician.

    Frequently asked questions

    What does CB class mean?
    The switch includes circuit breaker function; nameplate: Icm 7.65 kA, Icn 5 kA.
    Is the transfer without interruption?
    No. The manufacturer states that supply is interrupted during transfer, which takes up to 4 s.
    Are all phases monitored?
    No, the manufacturer states that only phase A is monitored. Use a phase monitoring relay if needed.
    Does it start the generator?
    No. The manufacturer states that the switch cannot turn the generator on or off.
    Can you help with selection?
    Yes. Send us the network type, incoming protection and generator power – we will help you choose the right switch.

    Automatic transfer switch ATS TAXNELE TXATS1 | 4P | 125 A | CB class

    CB class ATS with circuit breaker function – where an interruption of a few seconds is acceptable.

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.
  • Alternative products

    U-FTP Cable | 6A CAT | 4x2x23 AWG | shielded | copper | UV resistant | outdoor use | black
    Code: KIF6AOUTS500

    The U/FTP cable is a high-quality four-pair data transmission cable designed for telecommunication, industrial, and outdoor network installations. This cable is 100% copper, ensuring maximum signal transmission efficiency and minimal signal attenuation.

    It is adapted for 10 Gigabit Ethernet (10GBASE-T) data transmission at speeds of up to 10,000 Mbps and provides high electromagnetic resistance, as each pair is shielded with aluminum foil. Thanks to the PE outer layer, the cable is resistant to moisture, UV radiation, and mechanical impact, making it ideal for outdoor installations. 

    Price 0.73 € VAT incl.
    ( 0.60 € VAT excl. )
    Solar PV cable | H1Z2Z2-K | 1x4 mm² | black | 1.5 kV DC | EN 50618 | Dca | IEMMEQU HAR
    Code: H1Z2Z2K

    The cable is designed for connecting photovoltaic (solar energy) systems and interconnecting solar modules. This cable offers excellent resistance to ultraviolet (UV) rays, ozone, atmospheric effects, and temperature fluctuations. A durable and flexible single-core copper cable with double insulation ensures long service life and safe use even in the most challenging outdoor conditions. Suitable for installation both indoors and outdoors.

    Price 0.98 € VAT incl.
    ( 0.81 € VAT excl. )
    Network plug | RJ45 connector (8P8C) | for UTP CAT 6e cable | unshielded | through-plug | transparent
    Code: WT117

    This RJ45 Cat.6 UTP modular plug is a high-quality 8P8C unshielded network connector type, designed for Cat.6 UTP (Unshielded Twisted Pair) cables. The special straight-through design makes cable termination easier and more convenient, as the wires can be threaded through the plug, allowing a visual check of the wire arrangement before crimping the connector.

    Price 0.20 € VAT incl.
    ( 0.17 € VAT excl. )
  • privacy policy

    Information