Products catalog

Home/Product Catalog/Electrical distribution and installation/Electrical Energy Supply | Distribution Panels | Boxes | Accessories/Sealing products | seals for electrical wires | cables | panels | boxes
  • New item   Membrane cable entry plate with cones | for 216×84 mm cut-out | 43 cables Ø4–27.5 mm | grey | IP65 | HT Hi Tech Polymers | HTKC-43
    New item   Membrane cable entry plate with cones | for 216×84 mm cut-out | 43 cables Ø4–27.5 mm | grey | IP65 | HT Hi Tech Polymers | HTKC-43 1

    Membrane cable entry plate with cones | for 216×84 mm cut-out | 43 cables Ø4–27.5 mm | grey | IP65 | HT Hi Tech Polymers | HTKC-43

    Code: Sandariklis HTKC-43
    Inquire about this item
    Price 5.71 € VAT incl.
    ( 4.72 € VAT excl. )
    Want another price? Suggest yours!

    HTKC-43 is a membrane cable entry plate with cones for a 216×84 mm cut-out. It has 38 cones Ø7–12.5 mm for installation cables, 4 cones Ø4–10.5 mm for thin cables and one Ø14–27.5 mm for the supply cable. Sealing rating is IP65.

  • Product description

    Membrane cable entry plate with cones | for 216×84 mm cut-out | 43 cables Ø4–27.5 mm | grey | IP65 | HT Hi Tech Polymers | HTKC-43

    HTKC-43 is a TPE-SEBS elastomer plate for a standard 216×84 mm cut-out that takes up to 43 cables. Its core is 38 identical cones Ø7–12.5 mm – the typical range of installation cables. In addition there are 4 cones for thin cables and one large cone for an incoming cable up to Ø27.5 mm.

    Key point:
    In a distribution board most of the space is taken by identical outgoing circuit cables, while the incoming cable is much thicker. The HTKC-43 layout is designed for exactly that: many medium cones for circuits and one cone up to Ø27.5 mm for the incomer – more than HTC-50 (Ø15–25 mm). Four small cones remain for communication, bus or sensor cables.
    Cables
    up to 43
    Circuit cables
    38 × Ø7–12.5 mm
    Incomer
    1 × Ø14–27.5 mm
    Protection
    IP65

    How it works

    A 216×84 mm cut-out and Ø10 mm fixing holes (spacing 193 × 62 mm) are made in the enclosure, the plate is screwed on and its edge seals against the wall.

    A cone of suitable size is chosen for each cable, its tip is cut at a step slightly smaller than the cable's outer diameter, and the cable is pushed through.

    The cones grip the cables tightly (IP65), while unused cones remain closed for future circuits.

    Why choose HTKC-43?
    One plate covers the whole cable set of a typical distribution board – circuits, incomer and a few thin communication cables – without separate glands for each size.

    Technical specifications

    Product type Membrane cable entry plate with cones
    Code HTKC-43
    Manufacturer HT Hi Tech Polymers Oy (Finland)
    Entries and cable Ø 38 × Ø7–12.5 mm; 4 × Ø4–10.5 mm; 1 × Ø14–27.5 mm
    Max. number of cables 43
    Enclosure cut-out 216 × 84 mm (C-shape, FL21)
    Fixing holes Ø10 mm, spacing 193 × 62 mm
    Degree of protection IP65 (EN 60529)
    Operating temperature −40…+130 °C
    Material TPE-SEBS 50 ShA, halogen-free, oil-splash-resistant
    Colour grey (RAL 7035)
    Use indoor and outdoor

    Main functions

    • 38 cones Ø7–12.5 mm – for outgoing circuit installation cables
    • 1 cone Ø14–27.5 mm – for the incoming cable
    • 4 cones Ø4–10.5 mm – for communication, bus or sensor cables
    • Individual sealing – each cable in its own cone
    • Spare capacity in the plate – uncut cones stay sealed

    Where is it used?

    • Stairwell and floor distribution boards in apartment buildings
    • Circuit boards in offices and retail premises
    • Lighting and socket boards in industrial premises
    • Outdoor distribution cabinets (−40…+130 °C, IP65)
    • Boards in agricultural buildings and warehouses
    • Boards with a few bus or communication cables next to power circuits

    Use by need

    For distribution board builders.
    One plate model fits most circuit boards – fewer different glands in stock.
    For installers.
    Circuit cables go in fast, with no separate holes and nuts for each cable.
    For designers.
    The entry solution is clear in the specification: one 216×84 mm cut-out, up to 43 cables, IP65.

    Practical application

    If a stairwell board has 30 circuit cables Ø9–11 mm, an incoming cable Ø20 mm and 3 communication cables Ø6 mm, HTKC-43 takes them all and 8 medium cones remain for future circuits.

    Pros

    • 38 identical cones for typical circuit cables
    • Incomer cone up to Ø27.5 mm
    • Operating temperature −40…+130 °C
    • IP65, for indoor and outdoor use
    • Halogen-free, oil-splash-resistant material

    Cons / limitations

    • Only one thick cable; for several thick cables choose HTKC-28 (6 × Ø13–28 mm) or HTX-23
    • Does not provide strain relief – cables must be secured inside the board
    • Not for cables thinner than Ø4 mm
    • Not a fire barrier

    Safety and installation notes

    • Make the cut-out only with the power off and after checking there are no wires or devices behind the wall.
    • Clean swarf out of the board after drilling.
    • Cut the cone at a step slightly smaller than the cable's outer diameter; a cone cut too wide will not seal.
    • Secure cables inside the board and do not bend them sharply right behind the plate.

    Quick selection guide

    Cut-out 216×84 mm
    38 × Ø7–12.5 mm
    1 × Ø14–27.5 + 4 × Ø4–10.5 mm
    IP65, −40…+130 °C
    Suitable when you need:
    • many circuit cables of the same size
    • one thicker incoming cable up to Ø27.5 mm
    • spare capacity for future circuits
    Check before use:
    • the cables' outer diameters against each cone group
    • whether a 216×84 mm cut-out with Ø10 mm holes can be made in the enclosure
    • that there is no more than one thick cable
    Important reminder: HTKC-43 provides IP65 sealing of the entry, but it does not replace cable fixing inside the board and is not a fire-stop seal.

    FAQ

    How many cables can enter through HTKC-43?
    Up to 43: 38 cables Ø7–12.5 mm, 4 cables Ø4–10.5 mm and one Ø14–27.5 mm.
    How thick can the incoming cable be?
    The largest cone is for a cable with an outer diameter of Ø14–27.5 mm.
    Is HTKC-43 suitable for an outdoor cabinet?
    Yes, the material is intended for outdoor use, protection IP65, operating temperature −40…+130 °C.
    How is a cone cut?
    With a knife or scissors at a step slightly smaller than the cable's outer diameter.
    Can it replace an HTC-50?
    Yes, both plates are for the same 216×84 mm cut-out; only the entry layout differs.
    What if a cone has been cut too wide?
    Use that cone for a thicker cable or replace the plate – an oversize opening does not ensure sealing.

    Manufacturer documents

    Links open on external websites. Checked 2026-10-04. If data differ, the latest manufacturer edition applies – or contact us.

    HTKC-43 – plate for distribution boards

    The HTKC-43 membrane plate with cones for a 216×84 mm cut-out takes 38 circuit cables Ø7–12.5 mm, 4 thin cables and one Ø14–27.5 mm incomer, IP65.

    Illustrative image may have been created using AI. The appearance of the product may differ slightly from the image shown. Please refer to the technical specification.

  • Alternative products

    CYKY 5x4 | Copper power cable | CYKY-L 5G4 | 1m | black  
    CYKY 5x4 | Copper power cable | CYKY-L 5G4 | 1m | black
    Code: 91950413
    Price 3.68 € VAT incl.
    ( 3.04 € VAT excl. )
    Add to cart 

  • Subscribtion to new arrivals

    privacy policy

    Information